HYLAFAX-INFO(5F)

NAME
info - remote device capability database

DESCRIPTION
The info subdirectory in the HylaFAX spooling area holds information about the capabilities and status of devices that have been called. One file exists for each device, with the filename created from the remote device's fully-qualified phone number. Files have a simple ASCII format. Each line is of the form

[&]tag: value

where a tag identifies a capability and a value is either a string, number, or boolean value. An optional ``&'' at the front of the line indicates that the tag's value is locked down and should not be updated by the server. This facility is useful for restricting the capabilities used with a particular machine.

The following items are recorded:

    Tag	Type	Description
    calledBefore	boolean	device has previously answered at this number
    dialFailures	number	count of consecutive failed dial operations
    hasV34Trouble	boolean	there is difficulty sending to this destination with V.34
    hasV17Trouble	boolean	there is difficulty sending to this destination with V.17
    lastDialFailure	string	reason for last failed dial operation
    lastSendFailure	string	reason for last failed send attempt
    maxPageWidth	number	maximum page width in pixels in normal resolution
    maxPageLength	number	maximum page length in millimeters
    maxSignallingRate	string	maximum signalling rate (bits/sec) to use
    minScanlineTime	string	minimum scanline time
    pagerMaxMsgLength	number	length of longest allowed text message
    pagerPassword	string	password string send to service provider
    pagerSetupCmds	string	commands for setting up modem for a specific service provider
    pagerTTYParity	string	parity & # bits configuration for IXO/TAP communication
    pageSource	string	parameter to tell the paging central who we are
    pagingProtocol	string	protocol (IXO or UCP) for this provider
    remoteCSI	string	remote device Called Subscriber Identification
    remoteNSF	string	remote equipment Non-Standard Facilities information
    remoteDIS	string	remote Digital Identification Signal: capabilities
    sendFailures	number	count of consecutive failed send attempts
    dataSent	number	units of data sent to the destination in the last session
    dataSent1	number	units of data sent to the destination in the session previous to the last
    dataSent2	number	units of data sent to the destination in the session previous, previous to the last
    dataMissed	number	units of data sent to the destination which were missed or corrupt in the last session
    dataMissed1	number	units of data sent to the destination which were missed or corrupt in session previous to the last
    dataMissed2	number	units of data sent to the destination which were missed or corrupt in session previous, previous to the last
    senderConfusesPIN	boolean	this caller does not return to Phase B and resend the same page after PIN
    senderConfusesRTN	boolean	this caller does not return to Phase B and resend the same page after RTN
    senderDataSent	number	units of data sent by the sender in the last session
    senderDataSent1	number	units of data sent by the sender in the session previous to the last
    senderDataSent2	number	units of data sent by the sender in the session previous, previous to the last
    senderDataMissed	number	units of data sent by the sender which were missed or corrupt in the last session
    senderDataMissed1	number	units of data sent by the sender which were missed or corrupt in session previous to the last
    senderDataMissed2	number	units of data sent by the sender which were missed or corrupt in session previous, previous to the last
    senderFumblesECM	boolean	there is difficulty receiving from this caller with ECM
    senderHasV17Trouble	boolean	there is difficulty receiving from this caller with V.17
    senderSkipsV29	boolean	this caller does not use V.29 in the presence of V.17
    supportsBatching	boolean	accepts batching protocol
    supportsHighRes	boolean	accepts 196 line/inch images (obsolete)
    supportsVRes	number	vertical resolution support bitmask
    supports2DEncoding	boolean	accepts Group 3 2D encoding
    supportsMMR	boolean	accepts Group 4 encoding
    supportsPostScript	boolean	accepts Adobe POSTSCRIPT transfer protocol

The HylaFAX scheduler, faxq(8C), uses the information stored in this directory when deciding if a call should be placed and when preparing documents for transmission. If a remote device's capabilities are known, then document preparation is constrained and/or optimized according to the capabilities. Otherwise, documents are prepared without regard for the remote device's capabilities and if a capability mismatch is encountered the session is terminated and the documents are reformatted using the newly discovered capabilities.

The calledBefore item is used by faxsend to decide whether or not to redial a phone number when encountering certain errors. For example, if a dialing command results in a ``NO CARRIER'' result, then the number will not be retried unless the number has previously been dialed successfully.

The minScanlineTime item indicates the minimum scanline time parameter used for facsimile transmissions. Acceptable values are: ``0ms'', ``5ms'', ``10ms/5ms'', ``10ms'', ``20ms/10ms'', ``20ms'', ``40ms/20ms'', and ``40ms''. (Values of the form X/Y mean to use X for 98 lpi images and Y for 196 lpi images.)

The pagerTTYParity item specifies the communication parameters to use when communicating with the IXO/TAP service provider. Acceptable values are: ``even'' (7 bits, even parity), ``odd'' (7 bits, odd parity), and ``none'' (8 bits, no parity). If nothing is specified then ``even'' is used per the standard.

The pagerMaxMsgLength, pagerPassword, and pagerTTYParity items can be setup according to the requirements of a pager service provider; they typically are locked down so that their values are not lost during updates.

The pagerSetupCmds can be used to define AT commands for setting up the modem for a specific service provider. This value overwrites the settings defined in hylafax-config(5F).

The pageSource parameter can be used to tell the paging central who we are. It usually contains a SMS answerable mobile number. It is only used for the UCP part of sendpage(8C). Note: This parameter should be used from user-land sendpage(1) and will be removed later.

The pagingProtocol defines which protocol, UCP or IXO, should be used to send the message to the service provider. It defaults to ``ixo''; for UCP set ``ucp''.

NOTES
faxsend, pagesend, and faxq automatically create and update entries in the info directory, as required.

The data in this directory is simply a cache of remote capabilities and, except for locked down items, can be safely purged at any time. The faxcron(8C) script, for example, periodically purges unlocked entries in this directory that have not been accessed in 30 days.

When the first batching attempt fails then supportsBatching is set to false. It must be manually altered in order to re-enable batching to the destination.

Restricting the capabilities used with a particular machine to a value other than those that are mandatory can cause documents to be sent outside of an acceptable range for the receiver.

SEE ALSO
faxcron(8C), faxq(8C), faxsend(8C), pagesend(8C), hylafax-config(5F)